Disclaimer : Topic này chỉ dành cho các bạn thích vọc công nghệ , cho các bạn mơ mộng vì cơ hội dc thưởng thức game PS3 sau bao năm "chung thủy chờ đợi" .. Các bạn khác có thể đọc nhưng lưu ý các bạn muốn bày tỏ cảm tưởng "ko ủng hộ" có thể sang lập topic khác ... Thân
Còn đây là topic trong 4rum , có thắc mắc gì cứ nhảy vào hỏi : http://www.ps3news.com/forums/ps3-h...ps-jailbreak-ps3-exploit-released-112277.html
============================
Như vậy là chỉ với tầm 20$ cho các boarch at90usb646,teensy , teensy ++ ... các bạn có thể tự làm dc PSJailbreak . Lưu ý là đoạn code trên chỉ cho phép bạn run unsigned code ( tức là có thể cài cái backup manager vào ) để tránh vấn đề pháp lý , còn backup manager tìm ở đây thì chắc phải lên 4rum hỏi rồi ( link trên )
Yên tâm là các bác ở nhà mình cũng bắt đầu vọc, ko rõ 1 board 20$ thì các bác làm sau bán bao nhiêu nhỉ
. Mình đọc qua thấy cũng ko khó lắm
Link http://www.ps3news.com/PS3-Hacks/psgroove-open-source-ps-jailbreak-ps3-exploit-is-released/Recently we reported that the PS JailBreak PS3 modchip was successfully cloned, and today the PSGroove PS3 exploit arrives!
PSGroove is an open-source reimplementation of the PSJailBreak exploit for AT90USB and related microcontrollers.
The PSGroove for now allows the very same features as the PSJailBreak but without backup manager support, you can also now remove the dongle.
The original PSJailbreak dongle had a patch that would trigger the lv1 panic hypercall if the dongle wasn't in the list of connected devices.
Download: http://github.com/psgroove/psgroove
It should work on:
- AT90USB162
- AT90USB646
- AT90USB647
- AT90USB1286
- AT90USB1287
- ATMEGA32U4
- ... and maybe more.
Cloning
The repository uses the LUFA library as a submodule. To clone, use something like:
git clone git://github.com/psgroove/psgroove.git
cd psgroove
git submodule init
git submodule update
Configuring
Chip and board selection can usually be handled in the Makefile. In particular, update the MCU, BOARD, and F_CPU lines. Suggested values:
Teensy 1.0:
MCU = at90usb162
BOARD = TEENSY
F_CLOCK = 16000000
Teensy++ 1.0:
MCU = at90usb646
BOARD = TEENSY
F_CLOCK = 16000000
Teensy 2.0:
MCU = atmega32u4
BOARD = TEENSY
F_CLOCK = 16000000
Teensy++ 2.0:
MCU = at90usb1286
BOARD = TEENSY
F_CLOCK = 16000000
AT90USBKEY / AT90USBKEY2:
MCU = at90usb1287
BOARD = USBKEY
F_CLOCK = 8000000
Board-specific notes
Teensy boards only have one LED, so it will turn off when the exploit succeeds rather than turn green. Older Teensy 1.0 boards also have the polarity inverted. In general, a LED should do something when the board is powered, and do something different when the exploit works.
Building
On Linux, use the AVR GCC toolchain (Debian/Ubuntu package: gcc-avr). On Windows, WinAVR should do the trick.
make clean
make
Programming
Now program psgroove.hex into your board and you're ready to go. For the AT90USBKEY and other chips with a DFU bootloader preinstalled, you can get the dfu-programmer tool, put your board in programming mode, and run
make dfu
For the Teensy boards, you probably have to use the Teensy Loader software.
Using
To use this exploit:
- Hard power cycle your PS3 (using the switch in back, or unplug it)
- Plug the dongle into your PS3.
- Press the PS3 power button, followed quickly by the eject button.
After a few seconds, the first LED on your dongle should light up. After about 5 seconds, the second LED will light up (or the LED will just go off, if you only have one). This means the exploit worked! You can see the new "Install Package Files" menu option in the game menu.
Notes
A programmed dongle won't enumerate properly on a PC, so don't worry about that.
This software is not intended to enable piracy, and such features have been disabled. This software is intended to allow the execution of unsigned third-party apps and games on the PS3.
Read more: http://www.ps3news.com/forums/ps3-h...s3-exploit-released-112277.html#ixzz0yFfAIano
Còn đây là topic trong 4rum , có thắc mắc gì cứ nhảy vào hỏi : http://www.ps3news.com/forums/ps3-h...ps-jailbreak-ps3-exploit-released-112277.html
============================
Như vậy là chỉ với tầm 20$ cho các boarch at90usb646,teensy , teensy ++ ... các bạn có thể tự làm dc PSJailbreak . Lưu ý là đoạn code trên chỉ cho phép bạn run unsigned code ( tức là có thể cài cái backup manager vào ) để tránh vấn đề pháp lý , còn backup manager tìm ở đây thì chắc phải lên 4rum hỏi rồi ( link trên )
Yên tâm là các bác ở nhà mình cũng bắt đầu vọc, ko rõ 1 board 20$ thì các bác làm sau bán bao nhiêu nhỉ
. Mình đọc qua thấy cũng ko khó lắm
. Như vậy cái vi mạch chỉ cần sử dụng 1 lần duy nhất ( nếu bạn ko có ý định update firmware ) gì hết 
thế thì khác gì hack kiểu PSP nhỉ
Vậy chỉ cần ngoài shop mua 1 cái rồi cài cho ng dùng PS3 lấy 50k/lần là đc đấy 

( 50K vẫn còn là đắt )